==============================================================================dd
mzf2snd, a Sharp MZ file conversion utility
version 0.2.1
Usage: mzf2snd [-t wav|ogg] [-q <n>] [-a] [-o <outfile>] [-m rom|fsk|slow] [-s 1|2|3|4|5|6] [-l 0|1|2|3|4|5|6] [-p on|off] [-h -1|0|1] [-f 44k|48k] <filename>
 -t output file format
    wav - ms wav file, 8 bits/sample unsigned, mono
    ogg - ogg container with vorbis encoding, 16 bits/sample signed, mono, lossy compression
 -q encoding quality for lossy audio formats in range 0-10; 10 - best quality; 6 as default
 -a append to a file if exists. Output file specifications are taken from existing file in such case
    not applicable for 'ogg' file format
 -o output file; if not specified, 'filename' file is taken with extension changed accordingly to the sound file format and located in the actual directory
 -m modulation method:
    rom - format of Sharp MZ-800 rom; default
          practically reachable speed:7350 bits/s with '-s 6'; MZ800 polarity setting (DIP sw#4 and/or '-p' parameter) matters for speeds >4
          default -s (speed) for this method:1
          usable -s (speed) parameters: 1 to 6
          default loader: '-l 0' for '-s 1', '-l 1' for higher speeds
    fsk - pulse length detection; time between down edges measured
          practically reachable speed:14700 bits/s with '-s 6'
          default -s (speed) for this method:6
          usable -s (speed) parameters: 1 to 6
          default loader: '-l 4'
    slow - pulse length detection; time between down edges measured; 2 bits/pulse coded
          practically reachable speed:17640 bits/s with '-s 5'
          default -s (speed) for this method:5
          usable -s (speed) parameters: 1 to 5
          default loader: '-l 4'
 -s 1|2|3|4|5|6 transfer speed. 1-slowest, 6-fastest
 -l loader mode:
    0 - no loader
    1 - simple loader for used method
    2-6 - use in-header 'rom' preloader followed by method's loader of given speed in 'rom' format. This saves few seconds,
          but devalves lossy compression usability and probably decreases reliability a bit because of high speed 'rom' format usage
 -p signal polarity
    on - standard polarity; default
    off - reversed polarity
 -h pulse decision treshold modification; if a method does not work with your sound card/player setup, try -1 or 1 values
 -f sampling frequency; critical for fast speeds; use the value which your sound device physically use:
    44k - 44100 kHz
    48k - 48000 kHz
 <filename> - a MZF file to handle

==============================================================================dd
mzftransmit, a Sharp MZ file transmitting utility
version 0.2.1
Usage: mzftransmit [-m rom|fsk|slow] [-s 1|2|3|4|5|6] [-l 0|1|2|3|4|5|6] [-p on|off] [-h -1|0|1] [-f 44k|48k] <filename>
 -m modulation method:
    rom - format of Sharp MZ-800 rom; default
          practically reachable speed:7350 bits/s with '-s 6'; MZ800 polarity setting (DIP sw#4 and/or '-p' parameter) matters for speeds >4
          default -s (speed) for this method:1
          usable -s (speed) parameters: 1 to 6
          default loader: '-l 0' for '-s 1', '-l 1' for higher speeds
    fsk - pulse length detection; time between down edges measured
          practically reachable speed:14700 bits/s with '-s 6'
          default -s (speed) for this method:6
          usable -s (speed) parameters: 1 to 6
          default loader: '-l 4'
    slow - pulse length detection; time between down edges measured; 2 bits/pulse coded
          practically reachable speed:17640 bits/s with '-s 5'
          default -s (speed) for this method:5
          usable -s (speed) parameters: 1 to 5
          default loader: '-l 4'
 -s 1|2|3|4|5|6 transfer speed. 1-slowest, 6-fastest
 -l loader mode:
    0 - no loader
    1 - simple loader for used method
    2-6 - use in-header 'rom' preloader followed by method's loader of given speed in 'rom' format. This saves few seconds,
          but devalves lossy compression usability and probably decreases reliability a bit because of high speed 'rom' format usage
 -p signal polarity
    on - standard polarity; default
    off - reversed polarity
 -h pulse decision treshold modification; if a method does not work with your sound card/player setup, try -1 or 1 values
 -f sampling frequency; critical for fast speeds; use the value which your sound device physically use:
    44k - 44100 kHz
    48k - 48000 kHz
 <filename> - a MZF file to handle

==============================================================================dd
mzfinfo, the Sharp MZ file info utility
version 0.2.1
Usage: mzfinfo <filename>

==============================================================================dd